Siemens Schuckert D.III / D.IV 1/72 EASTERN EXPRESS 72154

 Siemens Schuckert D.III / D.IV
1/72 Aircrafts, Planes
Eastern Express EE72154

Manufacturer: Eastern Express
Scale: 1/72
Material: Plastic
Paint: Unpainted, Unassembled, Kit do not contain paints and glue.
Condition: New in Box

Siemens-Schuckert D.IV
D.IV replica displayed at Luftwaffenmuseum der Bundeswehr
Role	Fighter aircraft
National origin	Germany
Manufacturer	Siemens-Schuckert
First flight	1918
Introduction	1918
Primary user	Germany
Number built	123 (by the end of the war)

Siemens-Schuckert D.III
Role	Fighter
Manufacturer	Siemens-Schukert Werke
First flight	October 1917
Introduction	April 1918
Primary user	Luftstreitkräfte
Produced	80

Siemens-Schuckert built a number of designs in World War I and inter-war era. They also produced aircraft engines under the Siemens-Halske brand, which evolved into their major product line after the end of World War I. The company reorganized as Brandenburgische Motorenwerke, or simply Bramo, in 1936,^{[citation needed]} and were later purchased in 1939 by BMW to become BMW Flugmotorenbau.^[2]

Siemens-Schuckert designed a number of heavy bombers early in WWI, building a run of seven Riesenflugzeug. Intended to be used in the strategic role in long duration flights, the SSW R-series had three 150 h.p Benz Bz.III engines in the cabin driving two propellers connected to a common gear-box through a combination leather-cone and centrifugal-key clutch in SSW R.I to the SSW R.VII models(the SSW R.VIII utilized four engines). In the case of engine failure, which was extremely common at the time, the bomber could continue flying on two engines while the third was repaired by the in-flight mechanic. Two transmission shafts transferred the power from the gear-box to propeller gear-boxes mounted on the wing struts. Although there were some problems with the clutch system, the gear-box proved to be reliable when properly maintained. The SSW R.1 through the SSW R.VII designs were noted for their distinctive forked fuselage. Several of these aircraft (SSW R.V through the SSW R.VII) fought on the Eastern Front. Although interesting in concept, the cost of these and the R-types from other companies was so great that the air force eventually abandoned the concept until more practical designs arrived later in the war.

The first fighter designed at the works was the Siemens-Schuckert E.I which appeared in mid 1915, and was the first aircraft to be powered by the Siemens-Halske Sh.I, a newrotary, developed by Siemens-Schuckert, in which the cylinders and the propeller rotated in opposite directions. A small number of production machines were supplied to variousFeldflieger Abteilung to supplement supplies of the Fokker and Pfalz monoplane fighters used at the time mainly for escort work. The prototype SSW E.II, powered by the inline Argus AsII, crashed in June 1916, killing Franz Steffen, one of the designers of the SSW R types. By early 1916 the first generation of German monoplane fighters were outclassed by the Nieuport 11 and the Nieuport 17 which very quickly followed it; and Siemens-Schuckert were supplied with a captured Nieuport 17 to "study". The resulting SSW D.I was powered by the Siemens-Halske Sh.I, but was otherwise a fairly literal copy of the Nieuport 17. This aircraft was the first Siemens-Schuckert fighter to be ordered in quantity, but by the time it became available in numbers (well into 1917) it was outclassed by contemporary Albatros fighters.

Development of the Sh.I engine resulted in the 160 hp Sh.III, perhaps one of the most advanced engine designs of the war. The D.I fighter also formed the basis for a series of original designs, which by the end of 1917 had reached a peak in the Siemens-Schuckert D.III, which went into limited production in early 1918, and found use in home defense units as an interceptor, due to its outstanding rate of climb. Further modifications improved its handling and performance to produce the Siemens-Schuckert D.IV. Several offshoots of the design included triplanes and monoplanes, but none saw production.

With the end of the war production of the D.IV continued, mainly for sales to Switzerland who flew them into the late 1920s. With the signing of the Treaty of Versailles the next year all aircraft production in Germany was shut down. Siemens-Schuckert immediately disappeared, but Siemens-Halske continued sales of the Sh.III and started development of smaller engines for the civilian market. By the mid-1920s their rotary engines were no longer in vogue, but "non-turning" versions of the same basic mechanicals led to a series of 7-cylinder radial engines, the Sh.10 through Sh.14A, delivering up to 150 hp in the 14A. The Sh.14A became a best-seller in the trainer market, and over 15,000 of all the versions were eventually built.

Siemens-Halske no longer had any competitive engines for the larger end of the market, and to address this they negotiated a license in 1929 to produce the 9-cylinder Bristol Jupiter IV. Minor changes for the German market led to the Sh.20 and Sh.21. Following the evolution of their smaller Sh.14's, the engine was then bored out to produce the 900 hp design, the Sh.22. In 1933 new engine naming was introduced by the RLM, and this design became the Sh.322, when Siemens was given the 300-block of numbers. The Sh.322 design had reliability problems and never became popular.

The company reorganized as Bramo in 1936, and continued development of what was now their own large engine. Modifying the Sh.322 with the addition of fuel injection and a new supercharger led to the Bramo 323 Fafnir, which entered production in 1937. Although rather outdated in terms of design, by this time the engine had matured into a highly reliable powerplant despite its comparatively poor fuel economy, and 5,500 were produced until the lines shut down in 1944.

In design terms the 323 was basically a dead-end with little growth potential. By the start of the war its 1,000 hp was already at the low end of the performance scale, and use was limited to transports and bombers. In order to build a 1,500 hp-class engine Bramo started development of a two-row version of the engine as the Bramo 329, mirroring similar developments at BMW who were trying to scale up their Pratt & Whitney Hornet into the two-row BMW 139. Design of both engines was well advanced in 1939 when BMW bought Bramo, and cancelled work on the 329 to concentrate on what would become the excellent BMW 801.

Realizing the two-row radial development was a risky proposition; Bramo engineers had also started developing axial-flow jet engines in 1938. They were awarded a development contract to continue work on two designs, which would later become the 109-002 and 109-003 when the RLM officially started supporting jet development. The -002 used an advanced contra-rotating compressor for added efficiency, while the -003 used a simpler compressor/stator system that remains in use in modern designs today. The -002 proved to be too complex and work on it soon ended, but the -003 showed definite promise and eventually became the BMW 003.